100% Free CCNP Data Center 300-610 Dumps PDF Demo Cert Guide Cover
PDF Exam Material 2021 Realistic 300-610 Dumps Questions
NEW QUESTION 17
Refer to the exhibit.
The FCoE packets fail to be forwarded through the switch. What is the minimum MTU QoS requirement for the FCoE to work?
- A. 9000 bytes
- B. 2240 bytes
- C. 2158 bytes
- D. 2000 bytes
Answer: D
NEW QUESTION 18
Drag and drop the data center technologies from the left onto the correct descriptions on the right. Not all technologies are used.
Answer:
Explanation:
NEW QUESTION 19
Which two vSphere features must be included in the design of a Cisco HyperFlex systems stretched cluster?
(Choose two.)
- A. DRS
- B. VDP
- C. VSS
- D. FT
- E. HA
Answer: A,E
NEW QUESTION 20
Refer to the exhibit.
Which template is used when a vHBA template pair is created for a specific server that inherits its attributes from an existing template?
- A. Updating
- B. Initial
- C. Primary
- D. Secondary
Answer: B
NEW QUESTION 21
Refer to the exhibit.
A cloud provider service provider deployed three geographically separated Cisco ACI data centers. One of the customers needs to host a clustered application that is spread across the three data centers. The cluster nodes that host the application need a layer 2 topology to communicate with each other. Which Cisco ACI topology design meets these requirements?
- A. Multi-cloud
- B. Multi-pod over MP-BGP EVPN
- C. Multi-pod over OSPF EVPN
- D. Multi-site
Answer: D
Explanation:
Each data center has its own APIC cluster. This is multi-site setup.
NEW QUESTION 22
Drag the requirements from the left onto the correct policy types on the right.
Answer:
Explanation:
NEW QUESTION 23
Drag and drop the Cisco Nexus 7000 Series Switch resources from the left onto the correct groups on the right.
Answer:
Explanation:
NEW QUESTION 24
Drag the requirements from the left onto the correct policy types on the right.
Answer:
Explanation:
NEW QUESTION 25
Which feature must be configured to connect a classical Ethernet network to a data center network so that the data center network appears to be one large switch.
- A. VPC+
- B. UDLD
- C. OSPF
- D. EVPN
Answer: D
Explanation:
Section: Network Design
NEW QUESTION 26
Which address pool is used when a vHBA template is created?
- A. WWPN
- B. UUID
- C. IP
- D. MAC
Answer: A
Explanation:
Section: Automation Design
Explanation
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/gui/config/guide/2-1/ b_UCSM_GUI_Configuration_Guide_2_1/b_UCSM_GUI_Configuration_Guide_2_1_chapter_011010.html
NEW QUESTION 27
Drag and drop the Cisco Nexus 7000 Series Switch resources from the left onto the correct groups on the right.
Answer:
Explanation:
NEW QUESTION 28
Drag and drop the technologies from the left onto the correct descriptions on the right.
Answer:
Explanation:
NEW QUESTION 29
Which two automation requirements can be met by using Puppet? (Choose two.)
- A. Enable one-off infrastructure changes to be performed manually.
- B. Enable clients to pull changes without installing an agent.
- C. Push configuration updates immediately to servers.
- D. Provide support for writing new modules in Python.
- E. Enable clients to pull changes to configuration files.
Answer: C,E
NEW QUESTION 30
Drag and drop the feature descriptions from the left onto the correct UCS Fabric Interconnect modes on the right.
Answer:
Explanation:
NEW QUESTION 31
A network engineer must design a Cisco HyperFlex solution based on these requirements:
* two clusters in the main data center consisting of five HyperFlex nodes
* one edge node for the remote branch
* cluster nodes that use one rack unit of space
Which two devices should be used in the remote branch cluster for this design? (Choose two.)
- A. Fabric Interconnect 6300
- B. HX220C
- C. HX240C
- D. Gigabit Ethernet Switch
- E. UCSB B200
Answer: B,D
NEW QUESTION 32
Drag and drop the SAN components from the left onto the correct design considerations on the right.
Answer:
Explanation:
NEW QUESTION 33
Which factor determines the choice of platform designing a Cisco HyperFlex infrastructure to support computer-aided design applications?
- A. GPU support
- B. processor count
- C. storage capacity
- D. network speed
Answer: C
Explanation:
Section: Storage Network Design
NEW QUESTION 34
What can be implemented on Cisco Nexus 5600 Series Switches for link redundancy within a Fibre Channel fabric?
- A. SAN port channel
- B. vPC+
- C. E-Trunk
- D. LACP port channel
Answer: D
Explanation:
Section: Compute Design
NEW QUESTION 35
Drag and drop the configurations from the left onto the correct policies on the right.
Answer:
Explanation:
NEW QUESTION 36
After experiencing traffic disruptions from the failure of a single router, a customer asks an engineer to design a solution that will prevent this from occurring in the future. While examining the customer's environment, the engineer discovers that the routers are manufactured by a variety of different vendors, and they have varying amounts of CPU and memory resources. Additionally, several of the customer's applications require the ability to fine-tune the load-balancing parameters between multiple routers. Which solution should be used to meet these requirements?
- A. FHRP
- B. VRRP
- C. HSRP
- D. GLBP
Answer: B
Explanation:
Load balancing can be done by having different VRRP groups and configuring different servers with different default gateways. HSRP and GLBP are Cisco proprietary.
NEW QUESTION 37
What is a design consideration when implementing FSPF?
- A. Routes are based on the domain ID.
- B. Routes are based on the distance vector protocol.
- C. FSPF runs on a per-chassis basis.
- D. FSPF runs only on F Ports.
Answer: A
NEW QUESTION 38
An engineer finishes the initial set up of a VXLAN EVPN network. The engineer is asked to plan for connectivity that supports redundancy and extends multiple virtual routing and forwarding domains. The requirement is to use the same default gateway addressing across all leaf switches that belong to the VXLAN network. Which two solution must be used to meet these requirements? (Choose two)
- A. VRF-lite
- B. DC interconnect
- C. spanning tree protocol
- D. Distributed anycast gateway
- E. Inter-site network
Answer: B,D
Explanation:
Reference:
https://www.cisco.com/c/en/us/products/collateral/switches/nexus-9000-series-switches/white-paper-c11-739942.html
NEW QUESTION 39
An engineer must build a VXLAN flood-and-learn network. The customer requires the solution to be based on the IETF documented practice in RFC 7348. The solution must use broadcast, unknown unicast, and multicast (BUM) and include the efficient BUM and short BUM replication modes that use only shared trees.
Which technology meets these requirements?
- A. MVPN
- B. PIM sparse mode
- C. PIM SSM
- D. Bidirectional PIM
Answer: B
Explanation:
Reference:
flexpod_esxi70_vxlan_evpn_design.html
NEW QUESTION 40
Which two configuration methods can be used to deploy QoS to Cisco MDS Series switches? (Choose two.)
- A. multiple QoS policies that match individual devices
- B. multiple QoS policies that match multiple devices
- C. FCoE VLAN-based QoS
- D. zone-based QoS
- E. VSAN-based QoS
Answer: D,E
Explanation:
Section: Storage Network Design
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/mds9000/sw/7_3/configuration/qos/ cisco_mds9000_qos_config_guide/configuring_qos.html
NEW QUESTION 41
......
Exam Overview
Before going for the Cisco 300-610 test, you need to know the details of its structure and syllabus to be ready for the application. Thus, it is important to know that you will be given 90 minutes to clear 60 multiple-choice questions. To pass the exam, you should gain at least 825 points. Also, please note that the test is available in the English language and the voucher will cost you $300.
Other Study Options
For self-study, it is better to choose well-structured materials that ensure learning the topics one-by-one in a smooth manner. Amazon can also improve your learning with books like “How I Passed Designing Cisco Data Center Infrastructure Exam” by Rocismo Liolentz Publications. It is available in the form of Kindle edition and is focused on not just concepts of the exam but helpful test-taking tips and methodologies.
The Cisco 300-610 exam is designed to assess the students’ understanding of designing the infrastructure of data center by covering the following topics:
- Network Design (35%): This area implies that the potential candidates have knowledge of the Layer 2 connectivity concepts, such as endpoint mobility, availability of redundancy, convergence, and insertion of services. Their understanding of Layer 3 connectivity as well as its elements (IP mobility, graceful restart, and NSF, convergence) and insertion of services is also required. The applicants should be capable of evaluating various data center-related technologies, including vPC, vPC+, VXLAN EVPN, and OTV. Moreover, they need to have a comprehension of various options for routing virtualization and in-band/out-of-band for management.
- Storage Network Design (20%): As for this section, the test takers should demonstrate their knowledge of the iSCSI deployment plan, including addressing and multipathing schemes and QoS requirements in a data center (FCoE, Iscsi, Fibre Channel, FCIP). Furthermore, this part checks one’s ability to work with Fiber Channel interface, FCoE, and SAN network topology.
- Compute Design (25%): This domain includes the concepts of Ethernet connectivity, such as redundancy, over-subscriptions, and operation modes. Therefore, you must be capable of evaluating various options for storage connection along with the virtualization of network devices in data centers. This includes IOM uplinks, vCon, Ethernet adaptor policies, and policies for the Fiber Channel adapter. The individuals’ knowledge of various hyperconverged infrastructure options, such as cluster mode, desktop virtualization, and HX for the virtual server, is also necessary.
- Automation Design (20%): The final objective of the test deals with network orchestration along with its automation. Therefore, the examinees must understand DCNM, Inter-sight, NX-API, and Python and should be able to evaluate templates for service profiles, vNIC, vHBA, as well as global and local policies.
It is important to pay attention to every part of the exam content if you want to excel in the Cisco 300-610 test and earn the passing score, so be ready for a thorough preparation process.
Updated Cisco 300-610 Dumps – PDF & Online Engine: https://www.validtorrent.com/300-610-valid-exam-torrent.html
300-610.pdf - Questions Answers PDF Sample Questions Reliable: https://drive.google.com/open?id=1vklILXHrEGJWn3cuHqG_tzKR-LRPpz7l