FCSS_SDW_AR-7.4 Exam Dumps Pass with Updated 2025 Certified Exam Questions
FCSS_SDW_AR-7.4 Exam Questions - Real & Updated Questions PDF
NEW QUESTION # 10
When you use the command diagnose sys session list, how do you identify the sessions that correspond to traffic steered according to SD-WAN rules?
- A. You identify sessions steered according to SD-WAN rules with the data vwl_mbr_seq.
- B. You cannot identify SD-WAN sessions. You must use the sdwar. session filter.
- C. You identify sessions steered according to SD-WAN rules with the flag vwl.
- D. You identify sessions steered according to SD-WAN rules with the data sdwan_service_id.
Answer: D
NEW QUESTION # 11
Refer to the exhibit.
Refer to the exhibit that shows event logs on FortiGate.
Based on the output shown in the exhibit, what can you say about the tunnels on this device?
- A. The VPN tunnel HUB1-VPN1_0 is a shortcut tunnel.
- B. The master tunnel HU82-VPN3 cannot accept ADVPN shortcuts.
- C. The device steers voice traffic through the VPN tunnel HUB1-VPN3.
- D. There is one shortcut tunnel built from master tunnel VPN4.
Answer: C
NEW QUESTION # 12
Refer to the exhibits. The exhibits show two IPsec templates to define Branch IPsec 1 and Branch_IPsec_2. Each template defines a VPN tunnel. The error message that FortiManager displayed when the administrator tried to assign the second template to the FortiGate device is also shown. Which statement best describes the cause of the issue?
- A. You can assign only one template with a tunnel type of static to each FortiGate device.
- B. You should use the same outgoing interface of both templates.
- C. You should review the branch1_fgt configuration for configured tunnels in the rootVDOM.
- D. You can assign only one IPsec template to each FortiGate device.
Answer: D
NEW QUESTION # 13
Which statement describes FortiGate behavior when you reference a zone in a static route?
- A. FortiGate ignores the static routes defined through members referenced in the zone.
- B. FortiGate routes the traffic through the best performing member of the zone.
- C. FortiGate installs a static route for each member in the zone.
- D. FoftiGate installs ECMP static routes for the first two members of the zone.
Answer: C
NEW QUESTION # 14
Refer to the exhibit. The administrator analyzed the traffic between a branch FortiGate and the server located in the data center, and noticed the behavior shown in the diagram. When the LAN clients located behind FGT1 establish a session to a server behind DC-1, the administrator observes that, on DC-1, the reply traffic is routed over T2. even though T1 is the preferred member in the matching SD-WAN rule.
What can the administrator do to instruct DC-1 to route the reply traffic through the member with the best performance?
- A. FortiGate route lookup for reply traffic only considers routes over the original ingress interface.
- B. Enable reply-session under config system sdwan.
- C. Enable snat-route-change under config system global.
- D. Enable auxiliary-session under config system settings.
Answer: D
NEW QUESTION # 15
Refer to the exhibits.
You use FortiManager to configure SD-WAN on three branch devices.
When you install the device settings. FortiManager prompts you with the error "Copy Failed" for the device branch1_fat When you click the log button. FortiManager displays the message shown in the exhibit.
- A. Based on the exhibits, which statement best describes the issue and how you can resolve it?
- B. Check the metadata variable definitions, and review the per-device mapping configuration.
- C. Check the connection between branch1_fgt and FortiManager
- D. Remove the installation target for the SD-WAN member port4. You cannot combine metadata variable and installation targets.
- E. Gateways for all members in a zone must be defined the same way. Specify the gateway of the SD-WAN member port! without metadata variables.
Answer: A
NEW QUESTION # 16
When a customer delegate the installation and management of its SD-WAN infrastructure to an MSSP, the MSSP usually keeps the hub within its infrastructure for ease of management and to share costly resources.
In which two situations will the MSSP install the hub in customer premises? (Choose two.)
- A. The administrator expects a large volume of traffic between the branches.
- B. The customer expects a large amount of VoIP traffic.
- C. The majority of the branch traffic is directed to a corporate data center.
- D. The customer requires SIA with centralized breakout.
Answer: A,D
NEW QUESTION # 17
You manage an SD-WAN topology. You will soon deploy 50 new branches.
Which three tasks can you do in advance to simplify this deployment? (Choose three.)
- A. Update the DHCP server configuration.
- B. Create policy blueprint.
- C. Create model devices.
- D. Create a ZTP template.
- E. Define metadata variables value for each device.
Answer: B,C,D
NEW QUESTION # 18
The SD-WAN overlay template helps to prepare SD-WAN deployments. To complete the tasks performed by the SD-WAN overlay template, the administrator must perform some post-run tasks. What are two mandatory post-run tasks that must be performed? (Choose two.)
- A. Configure SD-WAN rules
- B. Assign an sdwan_id metadata variable to each device (branch and hub)
- C. Assign a hub id metadata variable to each hub device.
- D. Create policy packages and assign them to the branch devices.
- E. Configure routing through the overlay tunnels created by the SD-WAN overlay template.
Answer: A,D
NEW QUESTION # 19
Refer to the exhibits. You connect to a device behind a branch FortiGate device and initiate a ping test. The device is part of the LAN subnet and its IP address is 10.0.1.101.
Based on the exhibits, which interface uses branch 1_fgt to steer the test traffic?
- A. port1
- B. port4
- C. port2
- D. HUB1-VPN1
Answer: A
NEW QUESTION # 20
Refer to the exhibit.
An administrator checks the status of an SD-WAN topology using the FortiManager SD-WAN monitor menus. All members are configured with one or two SLAs.
Which two conclusions can you draw from the output shown? (Choose two.)
- A. The template view should be used to see the hub devices.
- B. One member of branch2_fgt is missing the SLAs.
- C. branch2_fgt establishes six tunnels to the hubs and they are all up.
- D. This SD-WAN topology contains only two branch devices.
Answer: B,D
NEW QUESTION # 21
Exhibit.
The administrator configured the IPsec tunnel VPN1 on a FortiGate device with the parameters shown in exhibit.
Based on the configuration, which three conclusions can you draw about the characteristics and requirements of the VPN tunnel? (Choose three.)
- A. The administrator must manually assign the tunnel interface IP address on the hub side
- B. This configuration allows user-defined overlay IP addresses.
- C. The tunnel interface IP address on the spoke side is provided by the hub.
- D. The remote end can be a third-party IPsec device.
- E. The remote end must support IKEv2.
Answer: A,B,D
NEW QUESTION # 22
Refer to the exhibit. An administrator configures SD-WAN rules for a DIA setup using the FortiGate GUI. The page to configure the source and destination part of the rule looks as shown in the exhibit. The GUI page shows no option to configure an application as the destination of the SD-WAN rule Why?
- A. You must enable the feature first using the GUI menu System > Feature Visibility.
- B. You cannot use applications as the destination when FortiGate is used for a DIA setup.
- C. FortiGate allows the configuration of applications as the destination of SD-WAN rules only on the CLI.
- D. You must enable the feature on the CLI.
Answer: B
NEW QUESTION # 23
Refer to the exhibit, which shows output of the command diagnose sys sdwan health-check status collected on a FortiGate device.
Which two statements are correct about the health check status on this FortiGate device?
(Choose two.)
- A. There is no SLA criteria configured for the health-check Level3_DNS.
- B. The interface T_INET_0 missed three SLA targets.
- C. The interface T_INET_1 missed one SLA target.
- D. The health-check VPN_PING orders the members according to the measured jitter.
Answer: A,C
NEW QUESTION # 24
Exhibit.
Two hub-and-spoke groups are connected through redundant site-to-site IPsec VPNs between Hub 1 and Hub 2 Which two configuration settings are required for the spoke A1 to establish an ADVPN shortcut with the spoke B2? (Choose two.)
- A. On hubs, auto-discovery-forwarder must be enabled on the IPsec VPNs to spokes.
- B. On hubs, auto-discovery-receiver must be enabled on the IPsec VPNs to spokes.
- C. On hubs, auto-discovery-forwarder must be enabled on the IPsec VPNs to hubs.
- D. On hubs, auto-diacovery-sender must be enabled on the IPsec VPNs to spokes
Answer: C,D
NEW QUESTION # 25
Refer to the exhibits.
The exhibits show two IPsec templates to define Branch IPsec 1 and Branch_IPsec_2. Each template defines a VPN tunnel. The error message that FortiManager displayed when the administrator tried to assign the second template to the FortiGate device is also shown.
Which statement best describes the cause of the issue?
- A. You can assign only one template with a tunnel type of static to each FortiGate device.
- B. You should use the same outgoing interface of both templates.
- C. You should review the branch1_fgt configuration for configured tunnels in the rootVDOM.
- D. You can assign only one IPsec template to each FortiGate device.
Answer: D
NEW QUESTION # 26
Refer to the exhibit.An administrator checks the status of an SD-WAN topology using the FortiManager SD-WAN monitor menus. All members are configured with one or two SLAs. Which two conclusions can you draw from the output shown? (Choose two.)
- A. The template view should be used to see the hub devices.
- B. One member of branch2_fgt is missing the SLAs.
- C. branch2_fgt establishes six tunnels to the hubs and they are all up.
- D. This SD-WAN topology contains only two branch devices.
Answer: B,D
NEW QUESTION # 27
You are planning a new SD-WAN deployment with the following criteria:
- Two regions
- Most of the traffic is expected to remain within its region
- No requirement for inter-region ADVPN
To remain within the recommended best practices, which routing protocol should you select for the overlays?
- A. IBGP within each region and between the regions.
- B. IBGP with BGP on loopback within each region and EBGP between the regions.
- C. OSPF for the routing within each region and EBGP between the regions.
- D. IBGP with BGP per overlays within each region and IBGP with BGP on loopback between the regions.
Answer: B
NEW QUESTION # 28
Refer to the exhibit.
An administrator configures SD-WAN rules for a DIA setup using the FortiGate GUI. The page to configure the source and destination part of the rule looks as shown in the exhibit. The GUI page shows no option to configure an application as the destination of the SD-WAN rule Why?
- A. You must enable the feature first using the GUI menu System > Feature Visibility.
- B. You cannot use applications as the destination when FortiGate is used for a DIA setup.
- C. FortiGate allows the configuration of applications as the destination of SD-WAN rules only on the CLI.
- D. You must enable the feature on the CLI.
Answer: B
NEW QUESTION # 29
Refer to the exhibit. The administrator used the SD-WAN overlay template to prepare an IPsec tunnels configuration for a hub-and-spoke SD-WAN topology. The exhibit shows the FortiManager installation preview for one FortiGate device.
Based on the exhibit, which statement best describes the configuration applied to the FortiGate device?
- A. It is a spoke device that establishes dynamic IPsec tunnels to the hub It can send ADVPN shortcut requests.
- B. It is a hub device. It will automatically discover the spoke devices and add them to the SD-WAN topology.
- C. It is a spoke device that establishes dynamic IPsec tunnels to the hub. The local subnet range is
10.10.128.0/23. - D. It is a hub device. It can send ADVPN shortcut offers.
Answer: D
NEW QUESTION # 30
The SD-WAN overlay template helps to prepare SD-WAN deployments. To complete the tasks performed by the SD-WAN overlay template, the administrator must perform some post-run tasks.
What are three mandatory post-run tasks that must be performed? (Choose three.)
- A. Assign a branch_id metadata variable to each branch device.
- B. Assign an sdwan_id metadata variable to each device (branch and hub).
- C. Configure routing through overlay tunnels created by the SD-WAN overlay template.
- D. Configure SD-WAN rules.
- E. Create policy packages for branch devices.
Answer: A,C,D
NEW QUESTION # 31
Within the context of SD-WAN, what does SIA correspond to?
- A. Remote Breakout
- B. Secure Internet Authorization
- C. Local Breakout
- D. Software Internet Access
Answer: A
NEW QUESTION # 32
In which SD-WAN template field can you use a metadata variable?
- A. You can use metadata variables only to define interface members and the gateway IP.
- B. Any field identified with an "M" in a circle.
- C. All SD-WAN template fields support metadata variables.
- D. Any field identified with a dollar sign (S) in a magnifying glass.
Answer: B
NEW QUESTION # 33
Refer to the exhibit.
Which statement best describe the role of the ADVPN device in handling traffic?
- A. This is a hub in a dual-region topology. The remote hub tunnel ID is 10.0.2.101.
- B. This is a hub that has received a query from a spoke and has forwarded it to another spoke.
- C. This is a spoke. The kernel received a shortcut request and forwards the query to another spoke.
- D. This is a spoke that has received a shortcut query from another spoke and has forwarded the response to its hub.
Answer: D
NEW QUESTION # 34
Which three characteristics apply to provisioning templates available on FortiManager? (Choose three.)
- A. A CLI template can be of type CLI script or Perl script.
- B. A template group can include a system template and an SD-WAN template.
- C. Each template group can contain up to three IPsec tunnel templates.
- D. A CLI template group can contain CLI templates of both types.
- E. CLI templates are applied in order, from top to bottom
Answer: B,D,E
NEW QUESTION # 35
......
Fortinet FCSS_SDW_AR-7.4 Exam Syllabus Topics:
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
Pass Guaranteed Quiz 2025 Realistic Verified Free Fortinet: https://www.validtorrent.com/FCSS_SDW_AR-7.4-valid-exam-torrent.html
Free Fortinet Certified Solution Specialist FCSS_SDW_AR-7.4 Ultimate Study Guide: https://drive.google.com/open?id=1g1OAUmIrgdGA3cjThcjAWYX1-5TjDaku