[2023] NS0-183 Dumps are Available for Instant Access
Valid NS0-183 Dumps for Helping Passing NS0-183 Exam!
Network Appliance NS0-183 (NetApp Storage Installation Engineer, ONTAP) Certification Exam is a professional certification exam designed to test the knowledge and skills of individuals who install and configure storage systems using NetApp ONTAP software. NS0-183 exam is intended for those who have experience and expertise in NetApp storage installation and configuration and are looking to validate their skills and knowledge in this area. Passing the NS0-183 exam is a key step towards becoming a NetApp Certified Storage Installation Engineer and demonstrates a strong understanding of the NetApp ONTAP software and its use in storage installation and configuration.
NEW QUESTION # 32
Click the Exhibit button.
After you install a FAS2720 with ONTAP 9.5, you disconnect the management port of node A to demonstrate cluster management LIF failover to the custom. When you reconnect the management port and try to revert the interface, you receive the following message.
Info: LIF "cluster_mgmt" has been hosted on port "NetApp-Cluster-01:e0M", whosehealth status is degraded.
You issue the network port showcommand and see the output shown in the exhibit. When you try to access the cluster interface, you cannot ping or connect to the cluster through the network.
Which two troubleshooting steps must you perform to solve the issue? (Choose two.)
- A. Set the Ignore Health Status parameter to false.
- B. Use the network port modify -up-admin command to administratively down and up the port.
- C. Reconnect the management cable to bring the port online.
- D. Set the Ignore Health Status parameter to true.
Answer: B,C
NEW QUESTION # 33
What is the maximum number of data disks that a RAID-TEC RAID group has?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
NEW QUESTION # 34
Click the Exhibit button.
Referring to the exhibit, what information is forwarded to syslog after you enter the scripted install commands? (Choose two.)
- A. SNMP traps
- B. EMS messages
- C. command history
- D. AutoSupport messages
Answer: C,D
NEW QUESTION # 35
Which hot-swappable transceiver is required to obtain full performance from a Cisco Nexus 3232C cluster-interconnect switch?
- A. SFP+
- B. SFP
- C. QSFP+
- D. QSFP28
Answer: D
NEW QUESTION # 36
In an ONTAP switched cluster, which three types of traffic travels over the cluster network? (Choose three.)
- A. Epsilon voting
- B. intracluster SnapMirror
- C. cluster database replication
- D. intercluster SnapMirror
- E. remote cluster peering
Answer: C,D,E
NEW QUESTION # 37
Click the Exhibit button.
You are reviewing the setup of a recently installed FAS9000 switched cluster. As shown in the exhibit, the cluster interconnects are connected to a pair of Cisco Nexus 3132Q-V 40 Gb ports.
For a high availability, which ports should swap Ethernet cables?
- A. Swap node1:e8a and node2:e4a.
- B. Swap node1:e4a and node1:e8a.
- C. Swap node1:e4a and node2:e4b.
- D. Swap node2:e4a and node2:e8a.
Answer: A
NEW QUESTION # 38
Which two SVMs are automatically created during the cluster setup? (Choose two.)
- A. data SVM
- B. system SVM
- C. admin SVM
- D. node SVM
Answer: B,C
NEW QUESTION # 39
Which three components are required when setting up a new ONTAP cluster? (Choose three.)
- A. intercluster IP
- B. password
- C. cluster management IP
- D. Advanced Drive Partitioning
- E. node management IP
Answer: B,C,E
NEW QUESTION # 40
You are setting up a new AFF A400 that will serve iSCSI LUNs. You will have four iSCSI SVMs that each need to connect to an Internet Storage Name Service (iSNS) for discovery and management purposes.
In this scenario, which network interface is needed for each SVM to register with the name service?
- A. intercluster LIF
- B. node management LIF
- C. SVM data LIF
- D. SVM management LIF
Answer: D
Explanation:
https://docs.netapp.com/ontap-9/topic/com.netapp.doc.dot-cm-sanag/GUID-E0C83978-2139-48C5-8C2B-80F4A385583E.html
NEW QUESTION # 41
You completed the installation of an AFF A700s with NetApp CN1610 switches. You used ports e0a and e0f with breakout cables to connect the controllers to the interconnect switches. After completing the cluster setup, ports e0e and e0i are not visible in OnCommand System Manager. In this scenario, what caused this problem?
- A. You are missing a license to enable those ports.
- B. This is a hardware error and you must open a case with NetApp Support.
- C. You must first enable the ports using the network port modifycommand.
- D. Breakout cables were used and the second port on the same ASIC became disabled.
Answer: C
NEW QUESTION # 42
You finished a new installation and executed Config Advisor successfully. You review the physical racking and cabling on one of the controllers, and notice an amber light that was not previously on.
Which two actions should you perform before you turn over the cluster for production? (Choose two.)
- A. Execute Config Advisor again to check for new errors.
- B. Let the customer know the cluster is operating normally while the amber LED is on.
- C. Remove cables connected to the controller until you find the one responsible for the controller issue.
- D. Review AutoSupport messages which could explain the controller state.
Answer: A,D
NEW QUESTION # 43
A customer wants to expand their 10-node AFF A700s SAN cluster on Cisco Nexus 3132Q-V interconnect switches. The customer has six AFF A700s nodes available.
In this scenario, what should you do to expand the cluster?
- A. Add six nodes to the existing cluster.
- B. Add two nodes to the existing cluster without exceeding the SAN cluster limit.
- C. Add an expansion module to each switch and then add the six nodes.
- D. Replace the switches with Cisco Nexus 5596T switches and then add the six nodes.
Answer: B
NEW QUESTION # 44
After performing a controller upgrade on an HA pair in an ONTAP 9.5 cluster, you want to decommission the old systems.
Which statement is correct in this scenario?
- A. Decommissioning is done automatically when the systems no longer send AutoSupport messages.
- B. Open a Priority 1 technical case with NetApp Global Support and specify "Decommission" in the title.
- C. The systems do not need to be decommissioned because the serial numbers are overtaken by the new systems.
- D. Ask the customer to log in to http://mysupport.netapp.com and decommission the old systems.
Answer: D
NEW QUESTION # 45
Click the Exhibit button.
You have an 8-node cluster, and sometimes the data LIFs fail over to a non-working port.
Referring to the exhibit, what must you do to solve this problem?
- A. Configure the LIFs using separate home nodes.
- B. Configure more than one IPspace.
- C. Configure the MTU consistently across the cluster.
- D. Configure the correct Ethernet ports in all broadcast domains.
Answer: C
NEW QUESTION # 46
Which three components are required when setting up a new ONTAP cluster? (Choose three.)
- A. intercluster IP
- B. cluster management IP
- C. password
- D. Advanced Drive Partitioning
- E. node management IP
Answer: A,B,E
NEW QUESTION # 47
You are asked to add a new HA pair to an existing 2-node switchless AFF A220 cluster. You must first convert to a 2-node switched cluster using Broadcom BES-53248 cluster switches.
Which two conditions must be fulfilled before you start the migration? (Choose two.)
- A. All cluster LIFs must be in the up state and on their home ports.
- B. The "Enabled Switchless Cluster" option must be manually set to "false".
- C. All cluster LIFs must have an MTU size of 1500.
- D. The 2-node switchless configuration must be properly set up and functioning.
Answer: A,D
NEW QUESTION # 48
You completed an ONTAP cluster deployment as a reseller engineer. During the knowledge transfer process to the customer, they ask for proof that the array has correct multi-path HA cabling deployed and that the array is error free.
Which documentation output would you present to the customer to satisfy this requirement?
- A. Active IQ OneCollect output
- B. NetAppDocs output
- C. Active IQ Unified Manager output
- D. Config Advisor output
Answer: D
NEW QUESTION # 49
A customer wants you to add a new AFF A700 HA pair to an existing 4-node AFF8080 EX cluster. The existing cluster uses NetApp CN1610 switches for the cluster connection and is using the recommended port count.
Which statement is true in this scenario?
- A. The AFF A700 is not supported with NetApp CN1610 switches/
- B. You cannot have more than four nodes with AFF.
- C. There are not enough ports available on the cluster switch.
- D. You cannot mix different AFF models in the same cluster.
Answer: D
NEW QUESTION # 50
A storage administrator is trying to upgrade a pair of FAS2520s with internal SATA storage to a new 2-node FAS8300 cluster. The storage administrator wants to preserve the existing data.
In this scenario, which two capabilities are available to the storage administrator? (Choose two.)
- A. the ability to convert the FAS2520s to disk shelves and attach them to the new nodes
- B. the ability to move the volumes from the old nodes to the new nodes
- C. the ability to create a 4-node MetroCluster across the four nodes
- D. the ability to pull out the tray of internal disks of the FAS2520s and reseat the tray in the internal storage of the FAS8300s
Answer: A,C
NEW QUESTION # 51
You just installed a new AFF A220 2-node cluster without additional disk shelves. When you review the Config Advisor output, you notice that your SAS cabling appears to be single-path HA.
In this scenario, which statement is true?
- A. The Config Advisor version you are using requires a plugin for AFF controllers.
- B. AFF A220 controllers with internal disks support only single-path HA.
- C. Cable controller 1 0a to controller 2 0a, and cable controller 1 0b to controller 2 0b.
- D. Cable controller 1 0a to controller 2 0b, and cable controller 1 0b to controller 2 0a.
Answer: D
NEW QUESTION # 52
......
Network Appliance NS0-183 exam is a comprehensive certification that validates a candidate’s knowledge and skills in NetApp storage installation. NS0-183 exam covers a range of topics, including installation and configuration, data protection, and troubleshooting. NetApp Storage Installation Engineer, ONTAP certification is recognized by the industry and can help candidates advance their careers and increase their earning potential.
Network Appliance NS0-183 certification exam is a great way to differentiate yourself from other IT professionals. NetApp Storage Installation Engineer, ONTAP certification is recognized throughout the industry as a mark of excellence in NetApp storage installation, and it can help you stand out in a crowded job market. Additionally, this certification can help you earn higher salaries and advance your career more quickly, as many organizations prefer to hire certified professionals for their IT positions.
Updated NS0-183 Dumps Questions For Network Appliance Exam: https://www.validtorrent.com/NS0-183-valid-exam-torrent.html